重型纸箱封箱机普遍故障及解决方法
Common faults and solutions of heavy carton sealing machine
重型纸箱包装后，都进生一个打箱，那麽就要使用封箱机来操作了，重型纸箱封箱机它的操作简易，是一种经久耐用的包装设备。是机械总会发生故障的情况下，那麽重型纸箱封箱机发生故障了大家如何来办呢。下边我们一起来了解下。
After heavy cartons are packed, there will be a dozen cartons, so it is necessary to use the sealing machine. The heavy carton sealing machine is easy to operate and is a kind of durable packaging equipment. When the machinery always breaks down, what should we do when the heavy carton sealing machine breaks down. Let's get to know each other.
封箱机操作简易，因此许多操作便会由于操作不合理发生一些故障。
The operation of the sealing machine is simple, so many operations will have some faults due to unreasonable operation.
故障一，封箱机的夹钉产生不够或姿势很慢
Fault 1: the nail clamping of the sealing machine is not enough or the posture is very slow
缘故：内片损坏，螺钉松懈或前扣轴的部位造成错动。
Cause: the inner plate is damaged, the screw is loose or the part of the front buckle shaft causes dislocation.
故障解决方法：拆换枪栓的内片或往上略微激发前扣轴或往下略微激发前扣轴，以后再各自试运转一下机器。
Troubleshooting: remove and replace the inner plate of the bolt, or slightly excite the front buckle shaft upward or slightly excite the front buckle shaft downward, and then try to run the machine separately later.
故障二：液压缸周边非常容易漏汽
Fault 2: steam leakage is very easy around the hydraulic cylinder
缘故及解决方法：主要是行为主体底端环因为长期工作的耗费损坏，应立即拆换底端环。
Cause and solution: it is mainly that the bottom end ring of the actor is damaged due to the cost of long-term work. The bottom end ring should be removed and replaced immediately.
故障三：枪栓处非常容易漏汽
Fault 3: it is very easy to leak steam at the bolt
缘故及解决方法：关键可能是切断阀环毁坏或电源开关座环毁坏，也应立即拆换。此外也有出气口非常容易漏汽，可能是发动机活塞毁坏，留意立即拆换。
Cause and solution: the key may be the destruction of the shut-off valve ring or the seat ring of the power switch, which should also be replaced immediately. In addition, the air outlet is very easy to leak steam, which may be the damage of the engine piston. Pay attention to remove and replace it immediately.
故障四：传动系统换没法精定位
Fault 4: the transmission system cannot be precisely positioned after replacement
缘故：可能是塑钢型材条或传动系统扭簧无弹性。
Reason: it may be that the plastic steel profile strip or the torsion spring of the transmission system is inelastic.
解决方法：先拆下来枪栓组成，把扭簧梢再次装上或替换一个新的塑钢型材条和传动系统扭簧。
Solution: first remove the bolt composition, install the torsion spring tip again or replace a new plastic steel profile strip and transmission system torsion spring.
之上便是重型纸箱封箱机普遍的故障及解决方法。
Above are the common faults and solutions of heavy carton sealing machine.
The wonderful content of this article is provided by heavy carton manufacturers. There are many wonderful contents on this website. You can click to enter more contents: https://www.gtmfpack.com We have special customer service to answer your questions
